Product Description

SealGreen Paver Concentrate Sealer with Salt Defense Technology

SealGreen Paver Sealer with Salt Defense Technology is a 5 year one component, VOC compliant, penetrating water repellent, which contains a proprietary modified siloxane. This water-based siloxane penetrates most masonry and concrete pores and capillaries up to ¼ inch or more depending on surface porosity and moisture content at the time of application. Applies with a pump sprayer.

SealGreen Paver Cleaner - Highly recommended for cleaning dirty pavers, mold and mildew without damaging your pavers.

ADVANTAGES
Effective on most vertical or horizontal exterior, above-grade paver surfaces. Natural substrate color and surface textures are unaffected, with little to no gloss created. Product ships in concentrate form to save on shipping cost.

Benefits of this product are:

Excellent resistance to water intrusion
Deep penetration into the substrate
Exhibits good beading effects
100% water vapor permeable
Mildew and fungus resistant
Efflorescence protection
High resistance to alkali attack
Freeze thaw protection
Can be reapplied to treated surfaces
Surface can be painted after sealer application

SealGreen Paver Sealer reacts with the silica in concrete and masonry in the presence of ultraviolet light and atmospheric moisture. This reaction forms strong permanent bonds beneath the surface and creates a hydrophobic zone that prevents water molecules from penetrating, while allowing free migration of water vapors. This eliminates stone or brick shedding. The chemical bonds formed in this process allow SealGreen Paver Sealer to become an integral part of the substrate and provide long-term water repellent protection. Recommended for concrete paver blocks, split face concrete blocks, exposed aggregate, concrete or stone foundation walls, clay bricks, cinder block, pavers, any type of concrete surface with large pores, bridges hairline cracks, prevents salts and deicers from penetrating. Allows the seal material to breath no moisture entrapment.

SealGreen Cleaners and Sealers are state-of-the-art protective treatments and have developed a reputation by architects and building professionals as the premier solution for water repellents and sealers. SealGreen is dedicated to solving the destructive influence water
intrusion and other elements have on building materials

The chemical bonds formed in this process allow SealGreen Paver Sealer to become an integral part of the substrate and provide long-term water repellent protection

To clean pavers or remove mold or mildew from surface we recommend using SealGreen Paver Cleaner

APPLICATIONS

Recommended surfaces include: architectural precast or cast in place, pavers, split face concrete blocks, brick, mortars, natural stones, limestone, granite, sandstone, terra cotta, ceramic tile and grout, adobe, exposed aggregate products, Portland cement stucco, plaster and concrete masonry units. Protects horizontal surfaces such as pavements, sidewalks and plazas. It should also be used on vertical surfaces with
leaks and or where extra protection is desired.

Also protects bridges, parking decks, airport taxiways and aprons, piers and marine structures, and other surfaces requiring outstanding corrosion resistance and protection from chloride penetration. For use on brick masonry to protect against the entrance of
wind-driven rain. To reduce the effects of mildew, efflorescence, and stains from concrete and masonry.

APPEARANCE
SealGreen Paver Sealer is clear, non-yellowing and does not change the color or appearance of typical surfaces to which they are applied. Buildings and structures stay cleaner because conditions which contribute to staining are reduced and dirt rinses away more readily.

PRETREATMENT FOR PAINT
Water can penetrate through most paints and coatings. This leads to damp substrates and blistering and peeling of paint. Pre-treating concrete, masonry, or stucco with SealGreen Paver Sealer prior to painting keeps walls drier and extends the life of the paint.
SealGreen Paver Sealer is compatible with most latex and other paints. But to assure compatibility between paint and pre-treatment, a small test application is recommended. Note: Do not use a pre-treatment or allow over-spray on metal or other nonporous surfaces to be painted.

TECHNICAL DATA

Color milky white
Active substance silane/siloxane
Active content 10%
Ph 5
Density 8.34#/gal.
VOC <50 g/l
TEST DATA
ASTM C 67 % Reduction in Water Absorption on Brick During
Immersion in Water for 24 hrs. Results – 96.9%
ASTM C 140 % Reduction in Water Absorption on 3000 psi
Concrete During Immersion in Water for 24 hrs. Results – 91.29%
ASTM C 97 % Reduction in Water Absorption on Indiana Limestone During Immersion in Water for 48 hrs. Results – 81.7%
ASTM C672 “Deicer Scaling” 100 cycles (deicer freezing and
thawing using air-entrained concrete specimens) Results - Little to No Change
ASTM E 514 “Water Permeance of Masonry” Reduction in Leakage 99.9%
ASTM D 1653 Water Vapor Transmission 100% Breathable

LIMITATIONS
Not intended for below-grade waterproofing. SealGreen Paver Sealer will leave a residue on non-porous substrates such as glass windows, metal frames and painted surfaces. Caution should be taken with specialty coated glass or plastic windows.
Check compatibility before application. Protect materials which can be damaged by solvents.

Do not apply when following conditions are present:
Ambient or surface temperature less than 40° F. Or predicted to fall below 40° F within 24 hours following application.
Rain within 72 hours prior to application or predicted within four hours after application. Wet or frozen
substrates. High winds which could cause excessive overspray.

Application should be completed by qualified applicator with experience applying water repellents. Application equipment should be clean and free of foreign materials which could be dissolved and deposited on surfaces to be treated. Contact SealGreen for additional precautions and information on compatibility with specific materials.

INSTALLATION

Best results are obtained by applying SealGreen Paver Sealer on clean and dry substrates. All surfaces must be cleaned to remove all traces of dirt, dust, efflorescence, mold, salt, grease, oil, asphalt, laitance, curing compounds, paint, coatings and other contaminants. Acceptable surface cleaning methods include shot-blasting, sandblasting, water-blasting and chemical cleaners. If chemical cleaning agents are used, neutralize and wash off residues completely. Allow surface to dry at least 72 hours after water cleaning. Check with SealGreen representative to verify suitable cleaning methods, products and that the surface preparation is adequate.

As a standard procedure, fresh concrete should be allowed to dry for 28 days before application. All re-pointing must be completed and allowed to cure at least 3 days. Concrete repair and replacement must be completed prior to application. Patching materials, caulking, sealing materials, traffic paint must be fully cured before applying SealGreen Paver Sealer. In addition, the actual amount of material that is used for each application is dependent on the absorptive capacity of the substrate. Before applying, it is recommended that preliminary tests be carried out to determine usage and to test the effectiveness of the treatment.

Application: Apply water repellents as early as practical to protect substrates during construction, but not before wall cap, flashing, and roof are in place and water trapped in structure has been drained.

Spray apply SealGreen Paver Sealer by low-pressure (150 psi maximum) pumping equipment with a fan type spray nozzle. Alternate methods include nap roller (1”) or by brush. Required application rate varies from 70 to 175 sq. ft. per gallon depending on surface texture and absorbency.

Vertical Surfaces: Mix well before using. Test small area before starting general application to assure desired results
and coverage rates. Apply when surface and air temperatures are between 40°F to 110°F. Provide adequate
ventilation.

Apply in a flooding application, from the bottom up so the material runs down 6 to 8 inches below the spray pattern. On horizontal surfaces the liquid material should pond on the surface at least 5 seconds before being absorbed. For best results two applications are recommended with the second application applied using a wet on wet technique, retreat within three to five minutes after initial application. A wet treated surface may be agitated with a soft bristle scrub brush to ensure more even distribution and greater penetration. During application, precautions should be taken to protect the surrounding area from over-spray. Remove over-spray from non-targeted surfaces immediately with soap and water. Apply to southern exposed areas during coolest part of the day.

Horizontal Surfaces: Mix well before using. Pretest to measure material coverage rates. Apply enough material so that solution stands for 60 seconds before completely penetrating the surface. If additional material is required to reach desired coverage rate, a wet on wet application can be used. Avoid puddling or ponding, brush or broom to spread material to more porous area. If applicable, block all drains and use absorptive coverings to contain run-off of excess material. To avoid unnecessary clean-up, use soap and water to remove over-spray as soon as possible.
Caution: Over application of material may cause darkening of surface.
Dry Time: To touch, or 2 to 6 hours depending on temperature and humidity.
Clean Up: Thoroughly rinse spray equipment with clean water. Wash rollers with soap and water. Rinse thoroughly.
Precautions: Fire hazards are eliminated since SealGreen Paver Sealer is water-based and does not contain combustible or flammable solvents. Respiratory protection is not required during normal use and handling. Please refer to the Material Safety Data Sheet for more detailed information.

LIFE EXPECTANCY
Five years when properly applied.

AVAILABILITY
SealGreen Paver is available in
concentrated form in 1-pint, 1-quart, 1 gallon, 55 gallon containers to approved applicators throughout the United States.
Contact ReUse Concrete Sealing Specialists, LLC at 800-997-3873 for a sales representative in your area.

TECHNICAL SERVICE
Technical service engineers are available to answer questions on product performance, application methods and chemical composition.

Product Videos

Custom Field

Product Reviews

Write a Review