- Driveways - Patios
- Stamped Concrete
- Garages & Warehouses
- Basements Interior Floors
- Humidity Testing
- Polished Concrete
- Brick & Stones
- Concrete Sealers
- Concrete Cleaners
- Color Stains
- Tools & Repair Products
- Snow & Ice Melt
- All Products
- Training Classes
We provide services to the following areas:
Mission Hills, KS
Overland Park, KS
Prairie Village, KS
Spring Hill, KS
Kansas City, MO
Lee's Summit, MO
We ship products to all 50 United States
We also ship International where PayPal is avilable
Vulkem 116 Crack Repair Caulk
|116 Crack repair Caulk Vulkem:||
Vulkem 116 Polyurethane Sealant for Horizontal and vertical Use - Limestone color
Picture: Crack repaired with Vullkem 116 and tooled with fingers soaked in dish soap.
INSTRUCTIONS: Cut tip on an angle. Puncture foil seal inside. Apply to clean, dry surfaces. Can be tooled dry, or with soapy water. Product meets ASTM C920-98 and CAN/CGSB 19.13-M87. Application information can be obtained from Tremco or ReUse your local Tremco distributor.
Product Description: Vulkem 116 is a one-part moisture-curing, gun-grade polyurethane sealant. Vulkem 116 is durable, flexible and offers excellent performance in moving joints. Vulkem 116 does not require a primer on most construction materials.
Basic Uses: Vulkem 116 is an excellent general purpose sealant designed for use in precast, masonry, window frame perimeters and similar types of construction joints. Vulkem 116 is suitable for continual immersion in water. Vulkem 116 is designed for exterior and interior use.
• Do not apply over damp or contaminated surfaces.
• Use with adequate ventilation.
Packaging: 10.1 US fl oz cartridges. (30 Tubes per box)
APPLICABLE STANDARDS: Conforms to U.S. Federal Specification TT-S-00230C, Type II, Class A and ASTM C920, Type S, Grade NS, Class 25, Use NT, M, T, A, I, O, and CAN/CGSD-19.13, MCG-2-25-B-N. Conforms to USDA approval standards.
Joint Design: May be used in any vertical or horizontal joint designed in accordance with accepted architectural/engineering practice. Joint width should be 4 times anticipated movement, but not less than ¼ inch (6.4mm) wide. Movement should not exceed 25% of the minimum joint width.
Joint Dimensions: For joints ¼ inch (6.4mm) to ½ inch (12.7mm) wide, the width to depth ratio should be equal. Joints ½ inch (12.7mm) wide or greater should have a sealant depth of ½ inch (12.7mm). Minimum joint size is ¼ inch by ¼ inch (6.4mm by 6.4mm).
Surface Preparation: For good adhesion, the joint interface must be sound, clean and dry. Depending on the substrates, or presence of form release agents, masonry waterproofing, dust, loose mortar or laitance, architectural paints or finishes, the joint surface may require a thorough wire bushing, grinding, sandblasting, solvent washing and/or primer.
Tooling & Cleaning: Use dish soap to tool with fingers. Tooling is recommended immediately after application to insure firm, intimate contact with the joint interface. Dry tooling is preferred. Excess sealant and smears adjacent to the joint can be carefully removed with Xylol or Toluol before sealant cures
CAUTION! Not intended for use by persons with pre-existing lung disorders or breathing problems or by those who have had a reaction to iscoyanates. Do not breathe vapors. Reports have associated repeated and prolonged occupational exposure to solvents with permanent brain and nervous system damage. Contains less that 115 gm of VOC per liter less water and less exempt solvent. (New Jersey statement: Contents of this container contain less that 1.0 pounds per gallon of VOC less water). Solvent contained is photochemically reactive.
Vapor harmful. May cause skin, eye and lung irritation and allergic respiratory reaction. Potential sensitizers. Long term overexposure to xylene may cause adverse kidney, liver or fetal development effects. Avoid ingestion, inhalation of vapors and contact with skin, eyes and clothing. Use only in well ventilated areas. If vapor concentration is unknown or exceeds exposure limits (e.g. TVs/PELs), wear suitable respiratory protection as indicated on the MSDS. Wear suitable eye, face and hand protection and other protective apparel. For additional health and safety information read the current MSDS carefully before using this product.
FIRST AID: Get medical attention immediately for any significant overexposure.
INHALATION: Leave area to breathe fresh air. Avoid further overexposure.
EYES: Flush immediately with running water for 15 minutes and get medical attention.
SKIN: Wash thoroughly with hand cleaner followed by soap and water. Get medical attention immediately if rash or other disorders develop.
INGESTION: Call nearest Poison Control Center or physician. DO NOT INDUCE VOMITING.